PART |
SPEC |
Accessory Drive Belt Tensioner Bolt - Lower |
16 lb ft |
|
|
Accessory Drive Belt Tensioner Pulley Bolt |
43 lb ft |
|
|
Automatic Transmission Flex Plate Bolts (1) |
•First Pass |
|
11 lb ft |
|
•Second Pass |
|
22 lb ft |
|
•Final Pass |
|
45 degrees |
|
|
Flywheel Bolts (1) |
•First Pass |
|
11 lb ft |
|
•Second Pass |
|
22 lb ft |
|
•Final Pass |
|
45 degrees |
|
|
Camshaft Position (CMP) Actuator Magnet Bolts |
89 lb in |
|
|
Camshaft Position (CMP) Actuator Solenoid Valve (1) |
•First Pass |
|
48 lb ft |
|
•Final Pass |
|
90 degrees |
|
|
Camshaft Position (CMP) Sensor Bolt |
18 lb ft |
|
|
Camshaft Position (CMP) Sensor Wire Harness Bolt |
18 lb ft |
|
|
Camshaft Retainer Bolts – TORX Head Bolts |
11 lb ft |
|
|
Connecting Rod Bolts (1) |
•First Pass |
|
15 lb ft |
|
•Final Pass |
|
85 degrees |
|
|
Coolant Temperature Sensor |
15 lb ft |
|
|
Crankshaft Balancer Bolt – Installation Pass with Used Bolt – to Ensure the Balancer is Completely Installed |
243 lb ft |
|
|
Crankshaft Balancer Bolt New Bolt with Flanged Head (1) |
•First Pass |
|
111 lb ft |
|
•Second Pass |
|
Loosen 360 degrees |
|
•Third Pass |
|
59 lb ft |
|
•Final Pass |
|
125 degrees |
|
|
Crankshaft Balancer Bolt New Bolt with Retained Rotating Washer (1) |
•First Pass |
|
111 lb ft |
|
•Second Pass |
|
Loosen 360 degrees |
|
•Third Pass |
|
59 lb ft |
|
•Final Pass |
|
200 degrees |
|
|
Crankshaft Bearing Cap Bolts (1) |
|
•Inner Bearing Cap Bolts - First Pass in Sequence1 |
•First Pass |
|
15 lb ft |
•Inner Bearing Cap Bolts - Final Pass in Sequence1 |
•Final Pass |
|
110 degrees |
|
|
•Outer Bearing Cap Bolts - First Pass in Sequence |
•First Pass |
|
15 lb ft |
•Outer Bearing Cap Bolts - Final Pass in Sequence |
•Final Pass |
|
|
•Bearing Cap Side Bolts – First Pass in Sequence |
•First Pass |
|
18 lb ft |
•Bearing Cap Side Bolts – Final Pass in Sequence |
•Final Pass |
|
60 degrees |
|
|
Crankshaft Oil Deflector Bolts |
89 lb in |
|
|
Crankshaft Position (CKP) Sensor Bolt |
18 lb ft |
|
|
Crankshaft Rear Oil Seal Housing Bolts |
18 lb ft |
|
|
•Cylinder Head Bolts - Internal Hex – LH Cylinder Head forwardmost fastener - First Pass in Sequence |
•First Pass |
|
59 lb ft |
•Cylinder Head Bolts – Internal Hex – LH Cylinder Head forwardmost fastener - Second Pass in Sequence |
•Second Pass |
|
90 degrees |
•Cylinder Head Bolts - Internal Hex – LH Cylinder Head forwardmost fastener - Final Pass in Sequence |
•Final Pass |
|
40 degrees |
|
|
•Cylinder Head Bolts – Standard Hex - First Pass in Sequence |
•First Pass |
|
59 lb ft |
•Cylinder Head Bolts – Standard Hex - Second Pass in Sequence |
•Second Pass |
|
90 degrees |
|
|
•Cylinder Head Bolts – Standard Hex - Final Pass in Sequence |
•Final Pass |
|
60 degrees |
|
|
Engine Block Coolant Drain Hole Plug |
44 lb ft |
|
|
Engine Block Coolant Heater |
37 lb ft |
|
|
Engine Block Oil Gallery Plugs – Front |
18 lb ft |
|
|
Engine Block Oil Gallery Plugs – Rear |
22 lb ft |
|
|
Engine Oil Cooler Adapter to Oil Pan Bolt (M6) |
89 lb in |
|
|
Engine Oil Cooler Adapter to Oil Pan Bolt (M8) |
18 lb ft |
|
|
Engine Oil Cooler Coolant Fitting |
26 lb ft |
|
|
Engine Oil Cooler Core Bolt |
18 lb ft |
|
|
Engine Wiring Harness Bolt (Rear Engine Channel) |
89 lb in |
|
|
Engine Wiring Harness Jumper Bracket Bolt |
18 lb ft |
|
|
Exhaust Manifold Bolts |
|
|
|
•Exhaust Manifold Bolts– If installing on existing cylinder head |
17 lb ft |
|
|
•Exhaust Manifold Bolts– If installing on NEW cylinder head |
20 lb ft |
|
|
Exhaust Manifold Heat Shield Bolts |
89 lb in |
|
|
Front Cover Bolts |
18 lb ft |
|
|
Fuel Pump Bolts |
18 lb ft |
|
|
Fuel Feed Intermediate Pipe Fittings (1) |
22 lb ft |
|
|
Fuel Feed Pipe Bolt |
89 lb in |
|
|
Fuel Injection Fuel Rail Bolts |
18 lb ft |
|
|
Fuel Injection Fuel Rail Crossover Pipe Bolt |
89 lb in |
|
|
Generator Bracket Bolts |
37 lb ft |
|
|
Ignition Coil Bracket-to-Valve Rocker Arm Cover Bolts |
89 lb in |
|
|
Intake Manifold Bolts |
|
|
|
•First Pass in Sequence |
•First Pass |
|
44 lb in |
•Final Pass in Sequence |
•Final Pass |
|
89 lb in |
|
|
Intake Manifold Cover Studs |
40 lb in |
|
|
Intake Manifold Cover Bolts |
40 lb in |
|
|
Knock Sensor Bolts |
18 lb ft |
|
|
Knock Sensor Heat Shield Bolt |
18 lb ft |
|
|
Oil Filter |
3/4 to 1 full turn after gasket makes contact with the sealing surface |
|
|
Oil Filter Fitting |
41 lb ft |
|
|
Oil Level Indicator Tube Bolt |
89 lb in |
|
|
Oil Pan Cover Bolts |
89 lb in |
|
|
Oil Pan Drain Plug |
18 lb ft |
|
|
Oil Pan Bolts – Oil Pan-to-Rear Housing |
106 lb in |
|
|
Oil Pan Bolts – Oil Pan-to-Rear Housing |
106 lb in |
|
|
Oil Pan Bolts – Oil Pan-to-Engine Block and Oil Pan-to-Front Cover |
18 lb ft |
|
|
Oil Pressure Sensor |
26 lb ft |
|
|
Oil Level Sensor Bolts |
89 lb in |
|
|
Oil Pump Screen Bolts |
89 lb in |
|
|
Oil Pump-to-Engine Block Bolts |
18 lb ft |
|
|
Positive Crankcase Ventilation Valve |
53 lb in |
|
|
Spark Plugs |
15 lb ft |
|
|
Throttle Body Bolts |
89 lb in |
|
|
Map Sensor Bolt – Intake Manifold |
40 lb in |
|
|
Evap Purge Valve Bolt |
89 lb in |
|
|
Timing Chain Tensioner Bolts |
18 lb ft |
|
|
Valve Lifter Guide Bolts |
106 lb in |
|
|
Valve LIfter Follower Guide Bolt |
106 lb in |
|
|
Valve Lifter Oil Manifold Bolts |
•First Pass in Sequence |
|
11 lb ft |
|
•Final Pass in Sequence |
|
22 lb ft |
|
|
Valve Lifter Oil Manifold Filter Plug |
22 lb ft |
|
|
Valve Rocker Arm Bolts |
22 lb ft |
|
|
Valve Rocker Arm Cover Bolts - In Sequence |
89 lb in |
|
|
Water Outlet Housing Bolts |
89 lb in |
|
|
Water Pump Impeller Bolts |
89 lb in |
|
|
Engine Coolant Manifold Bolts |
18 lb ft |
|
|
Starter Heat Shield Bolt - Side |
89 lb in |
|
|
Starter Heat Shield Bolt - Rear |
18 lb ft |